What is difference between A105 and A105N Round Bar?
The A105 and A105n round bars makes use of the same raw material but varies based on their heat treatment. The N means the bars is normalized for heat treatment, but the A105 bars doesn’t have any specific heat treatment requirements.
How do you calculate tolerance of A105 Round Bar?
The A105 round bar should be measured from 100mm from its end. It shall not exceed over 75% tolerance for a hot rolled round bars.
– The maximum shear stress in a solid A105 Carbon Steel Round Bars
– The A105 carbon steel round bars has a shear strength between 330 to 430mpa.
Cold Finished vs Cold Drawn A105 Bar Stock
Cold Finished vs Cold Drawn A105 Bar Stock
Cold drawn and finished A105 bar stock is produced at room temperature. In the cold drawing process, thin shaped products like wires, rods, etc. are produced. A cold finished A105 bars stock is a flat material which is produced by passing it through dies and shaping them. These bars exhibit a superior surface finish.
What is SA 105 Round Bar?
The SA 105 round bar is a grade of the circular bars that is designed for higher temperature and pressure systems. The SA105 round bars is specifically produced for boiler and pressure vessel equipment. These bars have enhanced dimensional tolerance and accuracy. The SA105 steel bar has a density of 8.08 g/cm3 and exhibits a melting point of 1425 degrees C. The steel bars can be put through various heat treatment procedures to enhance the quality of the SA105 bar. These bars have lasting performance and work well in reducing harsh environments. The SA 105 rod can be only produced in a circular cross section, unlike bars of this grade.
Difference between annealed and A105 Forged Bar
The A105 forged bars is produced via a forging process. Here, metal is shaped by hammering or rolling it at a particular temperature. ASTM A105 forged bars can be forged either at high, moderate, or cold temperatures. They help recover its yield strength and ductility. Annealing is also a part of the forging process. Here the metal is heated above its recrystallization value to increase its ductility and reduce its brittleness.
Specification of ASTM A105 Carbon Steel Round Bar

SA105 Round Bar and ASTM A105 Forged Bar in Annealed condition with Mill test reports in Middle East
ASTM A105 Bar Certifications
- NDT Test and Radiography Test
- Third Party Inspection
- Hardness Test
- Mechanical Testing
- Raw Materials Purchase Mill Certificate
- Chemical Analysis
- German Machine PMI Test
- According to International Criteria: EN 10204/3.1B
- Pitting Resistance Test
- IGC Test
ASTM A105 Hot Rolled Steel Bar Types

1/2″ ASTM A105 Carbon Steel Rod

6 Mtrs Hot Rolled ASTM A105 Flat Bars

3 meter ASTM A105 Carbon Steel Round Bar

20mm ASTM A105 Carbon Steel Rolled Flat Bar

2-1/2″ ASTM A105 Carbon Steel Threaded Bar

300mm Carbon Steel A105 Square Bar

3/4″ ASTM A105 Carbon Steel Flat Bar

12mm ASTM A105 Sheared & Edged Bar

30 Mm ASTM A105 Carbon Steel Pump Shaft Bar

80mm ASTM A105 Carbon Steel Bright Bars

39/64″ ASTM A105 Carbon Steel Half Round Bar

25mm ASTM A105 Black Bars

1200mm ASME SA105 Carbon Steel Half Round Bar

3/4″ ASTM A105 Carbon Steel Triangle Bar

3/8″ SA105 Hex Bar
Buy A105 Square Bar and A105n Round Bar at lowest price in Middle East, Get connected with trusted and genuine A105 Round Bar suppliers in UAE
ASME SA105 Steel Bar Price List
1-7/8 DIA X 14 FT LG SS ROUND BARS AS PER ASTM A105, BA FINISH
4.9/16 INCH DIAMETER X 3 METER LONG ASTM A105
DIA 120 MM ROUND BARS, CARBON STEEL ROUND BARS ASTM A 105
View SA105 Steel Bar and A105 Bar Stock standard sizes, specification, equivalent and price in Dubai
ASTM A105 Round Bar Equivalent

ASTM A105 Hot Rolled Steel Bar Chemical Composition

Carbon Steel A105 Rod Mechanical Properties

A105 Carbon Steel Round Bar and 1.0460 Bar according to EN 10060, UNS, DIN, ASTM, JIS, GB, BS, SAE, AISI International standard

ASTM A105 UNS K03504 Round Bar Weight Chart

Table of Content