Stainless steel equal lateral tee and forged lateral tee suppliers in UAE

The 45 degree threaded lateral tee is a common type of forged fitting. Here the fitting has a branch direction of 45 degrees to the run pipe. A 90 degree threaded lateral tee, on the other hand, has a branch direction which is at an angle of 90 degrees.
The stainless steel threaded lateral tee is designed with superior chemical content. This gives it tolerance against corrosive and oxidative media. The tees are designed in equal and reduced openings. The equal type allows for an even flow of fluids and gases to take place across its two inlet openings. The robust threaded reducing lateral tee has one of its openings reduced in size. This ensures that the flow in one of the channels is less than in the other.
The class 6000 threaded lateral tee is designed to handle higher volumes of media than ordinary tees. In comparison to this, the class 3000 is rated low in terms of pressure holding capacity.
What is NPT in threading of forged lateral tee?
An NPT lateral tee or the National Pipe Thread is an American standard of thread. The thread type is referred to as MPT for male threads, with FPT for female threads. The NPT forged lateral tee has flat peaks and valleys at a 60 degree angle.
How to Measure Threads of Screwed Lateral Tee?
Threads of a threaded reducing lateral tee is measured by calculating the width of the threaded part of the screw. This corresponds with the first number in the thread size. This is followed by measuring the thread spacing, which will give you the second number of the thread size.
What Is A Lateral Tee?
It’s a threaded fitting that is connected using threads. This is a special kind of tee whose branch directions are different from the straight tee. Here, the branch direction is 45 degrees to the run pipe. These tees help influence the characteristics of the flow within the system. A threaded lateral wye fitting is similar to a lateral tee, but they both have some differences in their design.
Threaded Lateral Tee Specification

Not finding specific size with your current stockists? Check list of very few but verified suppliers and get the perfect Threaded reducing lateral tee at best price in Dubai
Lateral Tee Price List
Price Per Piece |
Price in USD |
Price in UAE Dirham |
RED BW, WPB, 40/30, DN600X300, 45DEG Per Piece |
US $ 3749.55 |
UAE Dirham 13772.09 |
TEE CONNECTOR 1/4 NPT 3/8 OD CS Per piece |
US $ 5.30 |
UAE Dirham 19.48 |
STAINLESS STEEL 304L (45 DEG.) 50 NB Per Kg |
US $ 5.50 |
UAE Dirham 20.21 |
Carbon steel 45 degree Per Piece |
US $ 30.00 |
UAE Dirham 110.19 |
The price may vary as per the location, you may contact the verified manufacturers & suppliers listed on this page.
NPT lateral tee in 1/8 Inch to 4 Inch, dimensions as per ASME B16.11
Standard For Lateral Tee
- ASTM A182 / ASME SA182 – Wrought Austenitic Stainless Steel Piping Fittings Standard Specification
- ASME B16.11 – Socket Weld and Threaded Fittings
Lateral Tee Types
Weight Of Lateral Tee

How To Layout Lateral Tee

45 & 90 degree Threaded Lateral Tee with precison casting, check Threaded lateral wye fitting dimensions and sizes
Lateral Tee Dimensions

Difference Between Lateral Tee And Wye
A LATERAL is a straight run with a branch to one side. A TRUE WYE is a fitting with a trunk coming up that splits to a 45o branch left and right, resembling a “capital letter Y.”
45 Degree Lateral Tee Applications
- Chemical processing
- Textile
- Industrial equipment
- Petroleum
- Refining
- Waste treatment
- Pulp/paper
Why Purchase Stainless Steel Lateral Tee from below Supplier and Manufacturer?
- Ready Stock
- Wide range of material and sizes
- Material test certificate
- Third Party Inspection Certificates
- Delivery Options
- Packaging Options
Threaded equal lateral tee in NPT, PT, NPTF, G thread type
Different Types of Threaded Lateral Tee
Table of Content